これは役に立ちましたか?
製品のソフトウェアまたはファームウェアのアップデート | Bose Smart Ultra Soundbar
アップデートが利用可能になると、スピーカーは未使用の夜間に自動で更新されます。
お使いのスピーカーは毎日アップデートを確認します。アップデートが利用可能で、スピーカーがインターネットに接続されている場合は、自動でダウンロードおよびインストールされます。通常は夜間やシステムがアイドル状態のときに行われます。
アップデートがあるか確認するには：
- サウンドバーが動作しているインターネット接続のあるネットワークに接続されていることを確認してください。
ヒント：インターネット接続が機能しているかどうかは、音楽サービスをストリーミングしたり（設定済みの場合は）音声アシスタントに質問したりすることで確認できます。 - リモコンで、 音量＋ と ミュージック
ボタンを同時に10秒間長押ししてください。
- アップデートが利用可能な場合、更新中は白いライトがライトバー上を流れます。完了すると、サウンドバーが再起動します。
- アップデートが利用できない場合は、ライトバーの動作はなく、製品が再起動します。
標準のアップデート方法がうまくいかない場合は、以下の追加手段をお試しください
上記の手順は、Bose Smart製品をアップデートする最も簡単な方法です。アップデートには、Smart製品がインターネットに接続されていることと、ボーズアプリを使用していることが条件となります。標準のシステムアップデート方法が利用できない場合や動作しない場合は、代わりのアップデート方法をお試しください。
その他のアップデート方法
コンピューターとUSBケーブルを使ってアップデートする方法
To update your soundbar using a computer and a USB cable:
- On a computer, open an Internet browser and go to support.bose.com/UltraSB_FW to download the latest firmware update for your soundbar.
- When prompted, save the product_update.zip file. Do not rename, open, or unzip the file.
If a prompt to download the file does not appear, your browser may have downloaded the file automatically. Look for the file in a browser notification message or in the Downloads folder. - Connect a cable from the computer to the USB-C SERVICE jack on the back of the soundbar.
- Reboot the soundbar by disconnecting its power cord for 30 seconds.
- While waiting, verify it was unplugged by tapping the Microphone Off icon on the top of the soundbar. No tone should be heard after tapping the icon.
- After reconnecting the power cord, the light bar pulses white for about 30 seconds as the soundbar reboots.
- Once rebooted, the light bar turns off
- On the remote control, simultaneously press-and-hold the Mute and Music buttons for 5 seconds to enter Service mode. The light bar on the soundbar glows white then turns off when you release the buttons.
- In a separate web browser or tab, go to the following address: http://203.0.113.1:17008/update.html
IMPORTANT: This address will not work until you connect a computer, reboot your product then enter Service mode as described in the steps above - Select Choose File then select the update file downloaded earlier
- Click UPLOAD then wait for the file transfer to complete.
ダイレクトIP方式による更新
To update your soundbar using the Direct IP method:
- Go to support.bose.com/UltraSB_FW to download the latest firmware update for your soundbar.
- When prompted, save the product_update.zip file. Do not rename, open, or unzip the file.
If a prompt to download the file does not appear, your browser may have downloaded the file automatically. Look for the file in a browser notification message or in the Downloads folder. - Reboot the soundbar by disconnecting its power cord for 30 seconds.
- While waiting, verify it was unplugged by tapping the Microphone Off icon on the top of the soundbar. No tone should be heard after tapping the icon.
- After reconnecting the power cord, the light bar pulses white for about 30 seconds as the soundbar reboots.
- Once rebooted, the light bar turns off
- Once the soundbar finishes rebooting, determine its IP address. For more info, see Determining the IP address.
Be sure to check the IP address of the soundbar after rebooting since your router might assign it a new address. - In a web browser, type the IP address followed by :17008/update.html into the address bar (e.g. 10.0.0.6:17008/update.html) then press Enter.
- Select Choose File then select the update file downloaded earlier
- Click UPLOAD. The update file will begin to transfer and install.
- "UPLOAD COMPLETE" will appear in the browser once the file has been transferred to your soundbar.
- While the speaker is updating, a white light scrolls across the light bar on the front of the soundbar
- The update is complete when the light bar stops scrolling.
内蔵セットアップ用ネットワーク経由で更新する
To update your soundbar using the built-in setup network:
- Go to support.bose.com/UltraSB_FW to download the latest firmware update for your soundbar.
- When prompted, save the product_update.zip file. Do not rename, open, or unzip the file.
If a prompt to download the file does not appear, your browser may have downloaded the file automatically. Look for the file in a browser notification message or in the Downloads folder. - Restore the factory settings of the soundbar. For more info, see Resetting your product
- On your device that downloaded update file, open its Wi-Fi menu then connect to the network name that begins with Bose followed by the name of your soundbar.
If you are prompted that the connection has no Internet access, choose to connect to the network anyway. - In a separate web browser or tab, go to the following address: http://203.0.113.1:17008/update.html
IMPORTANT: This address will not work until you restore your product to the factory settings then connect to its built-in network as described in the steps above. - Select Choose File then select the update file downloaded earlier
- Click UPLOAD. The update file will begin to transfer and install.
- "UPLOAD COMPLETE" will appear in the browser once the file has been transferred to your soundbar.
- While the speaker is updating, a white light scrolls across the light bar on the front of the soundbar
- The update is complete when the light bar stops scrolling.
.png)
